Skip to content

Engineering Intro

Turning Concepts into Creations

  • Concrete
    • Admixtures
    • Concrete Strength
    • Shrinkage
    • Workability
    • Stress Strain Relationship
    • Serviceability
    • Reinforced Concrete
      • Introduction
  • Transportation
    • Binding Materials
    • Road Pavement
  • Mechanics
    • Support Reactions
    • Centriod
    • MOI
    • SFD & BMD
  • Statistics
    • Introduction
    • Probability
  • Contact Us

Utility Strike Prevention in 2026: Where Pre-Excavation Locating Works — and Where It Fails

On September 5, 2026 By Jalal Afsar

Pre-excavation locating reduces uncertainty; it does not certify that the ground is empty. The distinction …

Continue reading
Galvanized Steel Sheet

Choosing the Right Steel Plate Supplier

On March 18, 2026 By Jalal Afsar

Architectural Vinyl Wrap: Uses, Performance, and Common Failures

On January 23, 2026 By Jalal Afsar

How To Combine Aesthetics and Function in Landscape Engineering

On October 29, 2025 By Jalal Afsar

How Engineers Design Safer and Smarter Sports Surfaces

On October 29, 2025 By Jalal Afsar

Modulus Of Elasticity | Concrete Modulus | Initial Tangent Concrete Modulus | Procedure

On March 24, 2012 By Jalal Afsar In Stress Strain Relationship

Elastic modulus of concrete is not easy to determine, because of non-linear behavior of concrete. Concrete is very strong in compression but very weak in tension and this is the main reason for non-linear behavior …

Continue reading

Poisson’s Ratio Of Concrete | Lateral Strains | Longitudinal Strains | Poisson’s Ratio Limits

On March 23, 2012 By Jalal Afsar In Stress Strain Relationship

Poison’s ratio is the ratio between lateral strains and longitudinal strains. Poisson’s ratio, mathematically can be given as: V= – (lateral strain)/(longitudnal strain) When compressive force acts on a specimen then with the increase in …

Continue reading

Strains In Concrete | Strains Amount | Elastic Strains

On March 23, 2012 By Jalal Afsar In Stress Strain Relationship

Strain is the change in length as compared to original length that is before any variation. Strains in concrete are the reduction in volume of concrete after the application of loading then change in volume …

Continue reading

Stresses In Concrete | Example

On March 22, 2012 By Jalal Afsar In Stress Strain Relationship

Stress is defined as; ” force per unit area.” Stress is the combination of loads like dead loads, live loads, wind loads that will acts on the structure during construction and during service life. Mathematically …

Continue reading

Types Of Water Reducing Admixtures | Regular Plasticizers | Super Plasticizers

On March 20, 2012 By Jalal Afsar In Admixtures

Mainly water reducing admixtures are divided into two categories depending upon the amount of dose being use in concrete and in result the decrease in the required weight of water. Low range plasticizers or regular …

Continue reading

Water Reducing Admixtures | Cracking Index | Impermeability | Slump Value

On March 20, 2012 By Jalal Afsar In Admixtures

A type of chemical admixtures that are used as a replacement of water is known as water reducing admixtures. By using that kind of admixtures, amount of required water for a workable concrete will be …

Continue reading

Effect Of Air Entraining Admixtures On Strength

On March 20, 2012 By Jalal Afsar In Admixtures

Air entraining admixtures affect the strength of concrete up to large extent. Air entraining admixtures have almost 15-25% effect on strength as compared to normal concrete. By using air entraining admixtures strength of concrete diminishes.

Continue reading

Irrelevant Information In Resume

On March 18, 2012 By Jalal Afsar In Resume

There are many information which are not required in resume. One who mention these information,  may be his/her resume get rejected based on irrelevant information. Some employer felt childish when someone mention these kinds of information.

Continue reading

Avoid Resume Mistakes

On March 18, 2012 By Jalal Afsar In Resume

There are some very common mistakes that most applicants do while writing resume. While writing resume, focus towards the resume is very important. Your resume should show the employer very clear of what capabilities you …

Continue reading

References In CV

On March 18, 2012 By Jalal Afsar In CV Writing

References in your CV mean “to whom the company will contact to know about you? After they are interested to hire you”. When fresh graduates came in the field then they don’t have enough skills that …

Continue reading

Posts pagination

«Previous Posts 1 … 21 22 23 24 25 Next Posts»
WordPress Theme: Chronus by ThemeZee.
Go to mobile version