Skip to content

Engineering Intro

Turning Concepts into Creations

  • Concrete
    • Admixtures
    • Concrete Strength
    • Shrinkage
    • Workability
    • Stress Strain Relationship
    • Serviceability
    • Reinforced Concrete
      • Introduction
  • Transportation
    • Binding Materials
    • Road Pavement
  • Mechanics
    • Support Reactions
    • Centriod
    • MOI
    • SFD & BMD
  • Statistics
    • Introduction
    • Probability
  • Contact Us

Author: Jalal Afsar

Factors affecting crack width | Serviceability

On July 17, 2012 By Jalal Afsar In Serviceability

A beam will not fail if there is a good anchorage bond between steel and concrete. In such case, the beam will not be affected even bond get damaged along the entire span. If a …

Continue reading

Cracking In Flexural Members | Serviceability

On July 17, 2012 By Jalal Afsar In Serviceability

Most of the reinforced beams cracks because of a loading that are well below the service level. Restrained shrinkage becomes one of the possible reasons for cracking in members. Flexural cracking is not only because …

Continue reading

Short Term Loading | Elastic Modulus | Stress Strain Relation

On July 16, 2012 By Jalal Afsar In Stress Strain Relationship

How structure will perform when it goes under load? It’s all depends on the type of stress, stress strain relationship and the properties of the material from which it is made. The stress – strain …

Continue reading

Movement joints | Key Points | Structural Repairs

On July 15, 2012 By Jalal Afsar In Structural Repairs

When the temperature changes then expansion and contraction of bricks occurs in the structure and that cause cracking in the building. This happens, in case of no provision of movement joints in the structure during …

Continue reading

Concrete Conveying | Placing | Compacting

On July 13, 2012 By Jalal Afsar In Concrete, Uncategorized

Conveying of concrete from the mixer or from transit mixer truck for most of the building is done either in dump buckets or by pumping. During conveying, one of the most important risk is of …

Continue reading

High Strength Concrete | Requirements | Applications

On July 11, 2012 By Jalal Afsar In Concrete Strength

With the passage of time, technology is getting more advanced and there has been a rapid growth in the concrete properties. Concrete is improving day by day. There is not yet been an exact definition …

Continue reading

Concrete Quality Control | Curing Concrete

On July 11, 2012 By Jalal Afsar In Concrete Strength

The quality control is one of the most important aspects taken into account during the manufacturing of the materials. By little variation in water to cement ratio, strength drops very much. The cracking arises very …

Continue reading

Effect Of Temperature On Shrinkage | Thermal Coefficient

On July 10, 2012 By Jalal Afsar In Shrinkage

When exposed area is large then temperature effect is also considered. Because, concrete expands with the increase in temperature and in the same manner it contracts with the decreasing temperature. This type of change in …

Continue reading

Mineral And Chemical Admixtures

On July 10, 2012 By Jalal Afsar In Admixtures

Mineral admixtures and chemical admixtures are the extra ingredients other than water, cement, aggregates and fibers. These are added to the concrete batch plant during batch mixing or at the start when other quantities are …

Continue reading

Median | Procedure | Median Formulas | Example

On July 7, 2012 By Jalal Afsar In Introduction, Statistics, Uncategorized

It is the numeric value that separates the higher digit values from the lower digit values. It is represented by . The median has some limitations. Median can only be defined for dimensional data and …

Continue reading

Posts pagination

«Previous Posts 1 … 16 17 18 19 20 … 25 Next Posts»
WordPress Theme: Chronus by ThemeZee.
Exit mobile version